Half and Half & Hemp Oil

Half & Half

Half & Half (Pure Tung Oil & Citrus Solvent)
1 ounce  (covers 1 sq ft)
16 ounce covers 50 sq ft)
32 ounce (covers 100 sq ft)
1 Gallon (coverage 400 sq ft)

Half and Half
(A perfect blend of Pure Tung Oil and natural, food-grade thinner Citrus Solvent. Most projects require the thick viscosity of Pure Tung Oil to be thinned for better absorption into the surface. Half & Half is great for projects large and small. We’ve done the mixing so you don’t have to!)

Faifer & Company, Inc. is proud to announce that we are a distributor for D.O. SIEVER PRODUCTS (REAL MILK PAINT). We keep Half and Half and Hemp Oil in stock.

Half & Half Description

This is pre-mixed Pure Tung Oil and Citrus Solvent from the Real Milk Paint Co.

We found that is most cases the Pure Tung Oil is too thick to penetrate most surfaces. Thinning with a natural solvent helps the oil penetrate deeper into the material. The 1 to 1 or Half & Half ratio works great all-around for most surfaces like new raw wood, butcher block countertops, cutting boards, concrete, terra cotta clay pots, stone, and slate. This finish is also food contact safe! Generally, 3 to 5 coats are needed to seal and waterproof. This all-natural finish does take 7 to 10 days to develop a water resistance and a full 30 days for a complete cure. A quick way to see the color of your surface before oiling is to just wet with water. The way it looks wet but not glossy is the color you have when the oil is dry! Can be mixed with any other of our Tung Oil Products (i.e. Pure Tung Oil, Dark Tung Oil, Dark Half, Outdoor Defense Oil).

Direction for Use

Preparation

  1. The best operating temperature for applying Half & Half is above 50°F (10°C ).
  2. Be sure the surface of your project is free of dust, debris, or grime.
  3. Check to see if the surface is porous. (Half & Half works by absorbing into the material and filling the open pores. Therefore, if your material is not porous, it will not accept Half & Half. To test if your surface is porous or not, place a small amount of water on the surface. If the water absorbs, it is porous. If it does not and beads on the surface, you may need to sand and/or strip the surface.)
  4. If you need to sand your surface, we recommend not going above 220 grit sandpaper. Too high of a sandpaper grit will “polish” the surface, hindering proper absorption of Half & Half.
  5. We recommend using water or alcohol-based stains on the wood before the Half & Half is applied. Most oil-based stains should be avoided as they tend to seal the wood and prevent absorption of the Half & Half.
  6. DO NOT use a wood conditioner. This will seal the wood and prevent the tung oil from absorbing.
  7. NOTE: Only very old, dry wood or concrete tend to use unthinned Pure Tung Oil.
  8. Extremely dense woods such as teak, ipe, etc may require thinning Half & Half with more solvent (up to 2 parts solvent to 1 part tung oil. Half & Half is already at a 1 to 1 ratio of solvent to tung oil) You can use Citrus Solvent as a natural, food contact safe thinner!
  9. If you’re looking for a wood finish that doesn’t require any solvent, you may be interested in Hemp Oil

Application

When applying Half & Half, here’s a handy thing to remember: Apply, Absorb, Repeat or Remove

Apply – Apply the Half & Half to the surface.

Absorb – Let the oil absorb into the material.

Repeat – Do what you just did, apply the oil and let it absorb.

Remove – When the oil isn’t absorbing and pooling on the surface, remove it with a rag.

Cure – Let the tung oil go through its natural curing process.

For the best results, you want to saturate the material with the half & half to the point where a majority of the surface is no longer absorbing the oil. This will look like puddles on the surface even after waiting 40 minutes. Just like a sponge, the wood (or other porous surfaces) will only absorb so much oil before it can’t anymore. This saturation is achieved by doing multiple coats.

You can apply Half & Half with a brush, rag, roller, or even a pump sprayer depending on your project and needs. We recommend brushes and/or foam rollers for most projects.

  1. Apply a generous first coat.
  2. Let the half & half absorb into the surface, waiting if needed, up to 40 minutes.
  3. Apply another coat, let it absorb, and repeat the previous steps.
  4. Continue this process until you reach the desired amount of coats or have fully saturated the wood. You can tell the wood is saturated when the oil puddles on the surface and no longer absorbs oil across a majority of the surface. To be sure, wait 40 minutes. If the oil is still puddling, then you will know the surface is saturated.
  5. Taking a clean rag or cloth, remove any excess tung oil that is puddling or pooling on the surface.
  6. Hang those oil-soaked rags outdoors to dry. DO NOT pile the rags or put them in a container.

For the best finish, we recommend letting this application rest and settle overnight. The following day, apply one or two more coats of Half & Half to the surface of your project, following the same steps outlined above.

Cure – Half & Half does not contain any additives to speed the drying process, such as heavy metallic dryers. Because of this, it can take up to 30 days to completely/thoroughly cure by its natural polymerization process. Provided below are some guidelines to follow during the curing phase.

  1. Half & Half cures best in warm, well-ventilated places. The warmer and more ventilated the area, the faster it will cure.
  2. Placing objects on the surface will “suffocate” and prevent the tung oil from curing properly. If there is no airflow between the surface and the object, it should be removed until the curing is complete (30 days).
  3. During the first 15 days of curing, you can use the surface. However, you will want to avoid getting it dirty or allowing liquids to puddle on the surface during this period.
  4. As the Tung Oil cures, its durability and resistance to liquids and dirt will also increase. The first 7-15 days is when the oil is at its freshest and weakest state. After that point, increased regular use of the surface can take place.
  5. As the Half & Half cures, it slightly expands and may push fresh oil back to the surface. Check for oil that may be seeping to the surface and remove it, if found, with a rag.

For butcher block, wood countertops, and etc.

  1. Avoid getting dirt, water, or other liquids on the surface of the butcher block for at least the first 7-10 days.
  2. We recommend putting wax paper down near sinks when doing dishes and other activities that splash water about. This will prevent the water from pooling on the surface and can be easily removed after dishwashing.
  3. Avoid putting cutting boards, appliances, dishes, and other objects that sit close to the recently refinished surface for extended periods of time. These objects prevent airflow and can hinder the tung oil from curing.
  4. If you are mounting or under mounting a sink, we recommend waiting for 7-10 days before mounting the sink. For caulk, we recommend using DAP Ultra Clear All Purpose Sealer. Silicone caulks tend to pull away from the oiled surface over time.
  5. If you have an under-mount sink, we highly recommend saturating the end grain of the butcherblock in the sink area with 100% Pure Tung Oil. This will help seal the very porous ends of the wood and give it the best resistance to water.

For indoor floors

  1. Feel free to move about on your floors with either socks or rags underfoot after applying the Half & Half. Moving across the floor with rags or cloth material is actually recommended as it will help buff and prevent any oil that may seep to the surface.
  2. You can move furniture back into the room after applying the Half & Half. However, keep area rugs and furniture that sits close to the floor off until the full 30 days are complete. We recommend placing plastic sliders between the floor and wooden legs of furniture. This will prevent the furniture leg from naturally pulling the oil out of the floor.
  3. While the oil is at its freshest (usually the first 7-15 days) do not walk across the floor with dirty shoes. The dirt will be pressed into the fresh oil and will be hard to remove.
  4. The floors can be temporarily covered with plastic, painters cloths, or cardboard for no more than a day.
  5. Avoid having any liquids sit on the surface.

For outdoor decks, siding, and other wooden surfaces

  1. Freezing temperatures can affect the curing of tung oil. You will want to delay your project until the temperatures will be above freezing for a minimum of two weeks during the curing of the tung oil.
  2. Do not apply the Half & Half in the direct sunlight. The heat from the sun will flash polymerize the tung oil while it is on the surface.
  3. Try to apply Half & Half when rain is not in the forecast for a week or two. None of us can control the weather and should it rain on your newly oiled deck don’t worry. As soon as possible, remove the water from the surface using a leaf blower or a broom. You just want to prevent the water from staying on the newly finished surface.

Tips

  1. Do not apply or leave fresh tung oil on a surface in direct sunlight. This will flash cure it on the surface and will turn white.
  2. Do not sand between coats of tung oil. This is an application technique for tung oil varnishes, not 100% tung oil.
  3. Do not use tung oil over oil-based sealers, stains, and finishes.
  4. We recommend using a water-based stain to change the color of wood before tung oil is applied if a color other than that provided the tung oil is desired. For a darker, all-natural, tung oil finish check out our Dark Tung Oil and Dark Half products.
  5. Do not use the “green” thinners now being sold. They contain water and will not mix with the oil.
  6. Remember by adding petroleum mineral spirits or other thinners, the oil may become toxic with these substances mixed into it, although the finish produced is not toxic because the thinners evaporate.
  7. The number of coats of oil to be applied will be determined by the intended use of the piece. One to two coats is enough for decorative work, paneling and molding. For surfaces that receive moderate to heavy use or handling need a minimum of three and on up to six coats for maximum protection.
  8. Applying tung oil until the surface becomes fully saturated will give the best results. This will be evident as the surface will not absorb more oil.
  9. Renewal and/or maintenance coats are thinly applied with lint-free cloths (old bed sheets work well) or old t-shirt material on an as need be basis. A two parts solvent to one part tung oil mixture is recommended for maintenance coats.
  10. Do not get hung up on the number of coats, let the wood tell you when it has reached its maximum saturation.
  11. Tung Oil will be in the wood up to the surface not on the wood like varnish or polyurethane topcoat. The end result is more like seasoning a cast iron pan. This product will give you a surface that will stand up to vigorous use and spills: water will bead on the surface.
  12. After the tung oil has completely cured (30 days) cleaning of the surface can be done using hot water and mild soap, such as dish soap. Avoid using harsh chemicals or acids for cleaning.

Maintenance

The beautiful thing about a Pure Tung Oil finish is that the maintenance of it is easy. We recommend cleaning the floor with mild soap and hot water. Avoid using harsh chemicals, acids, or strong solvents to clean the surface.

Maintenance coats are on an as-need basis. Outdoor projects may require more maintenance than indoor. Heavily used areas can be expected to require more maintenance than lightly used areas. Typically, surfaces that need maintenance have a very dry, or lackluster appearance compared to when the finish was originally applied.

When doing a maintenance coat you do not need to sand the surface again. Here is what we recommend;

    1. Make sure the surface is clean and free of dust or debris.
    2. Make a 2 to 1 ratio of solvent to Pure Tung Oil (2 parts solvent, 1 part tung oil). This thinned mixture can easily find any open pores and fill them.
    3. Thinly apply this mixture using a clean cloth. Simply wipe it onto the surface, no need to lather it on.
    4. Wipe up any excess that may be on the surface with a clean, lint-free rag or cloth.
    5. Allow this thin coat to cure for 24 hours.
    6. Hang oil-soaked rags outdoors to dry.
    7. Go back to enjoying the surface like normal!

Storage 

Half & Half can last with ease for multiple years on the shelf. Here are some guidelines to help you store it properly so it can be used for your next project.

  1. Make sure the lid on the Half & Half packaging is tightly screwed on. This will keep air exchange from happening in the container.
  2. Store the bottle in a dry, moderate temperature environment. A place where it won’t freeze or become excessively hot. Freezing of the oil will make the natural fats separate from the oil. Excessive heat can cook the oil to the point where it cures in the bottle.

Ingredients 

We believe in being honest with what is in our products. So, thats why we provide the ingredients used in them so you can rest assured knowing exactly what is in the product you purchase from us. It’s just a way we make it easier on you.

Half & Half is made of

  • Pure Tung Oil
  • Citrus Solvent

Pure Tung Oil is approved for food contact by the FDA. View document.

Citrus Solvent is a biodegradable, naturally-occurring solvent, as the main component is simply citrus peel oil. Citrus Solvent’s interesting chemical properties, pleasant citrus aroma, and is FDA-GRAS rating (“generally recognized as safe”), view document. Citrus Peel Oil is extracted from citrus rind. When citrus fruits are juiced, the oil is pressed out of the rind. This oil is separated from the juice and distilled to recover certain flavor and fragrance compounds. The bulk of the oil is left behind and collected as “food grade” citrus oil. After the juicing process, the peels are conveyed to a steam extractor. This extracts more of the oil from the peel. When the steam has been condensed, a layer of oil then floats on the surface of the condensed water. The result is technical grade citrus peel oil, which is the main ingredient in our Citrus Solvent.

Take a look at our Half & Half Safety Data Sheet (SDS) by clicking here.

Gallery

PRODUCTS OFFERED

Hemp Oil

Hemp Oil
1 ounce (covers 1 sq ft)
8 ounce (covers 25 sq ft)       
16 ounce covers 50 sq ft)
32 ounce (covers 100 sq ft)
1 Gallon (coverage 400 sq ft)

Hemp Oil
Hemp Oil dries to a matte finish and will not produce a gloss or even much sheen. Boasting qualities such as food contact safe, hypoallergenic, all natural VOC’s, and no need for a solvent to thin the oil. This naturally thin viscosity oil will penetrate porous surfaces well. Use on bare wood, over milk paint, chalk paint, cutting boards, carved utensils, and to revive old wood finishes.

Faifer & Company, Inc. is proud to announce that we are a distributor for D.O. SIEVER PRODUCTS (REAL MILK PAINT). We keep Half and Half and Hemp Oil in stock.

Hemp Oil Description

Squeezed from industrial hemp plants. Very light nutty aroma. Dries to a matte finish. Will never produce a gloss or even much sheen.

All natural VOC’s and solvent-free drying oil finish. Hemp oil by The Real Milk Paint Co. can be used on bare wood, over milk paint, chalk paint, and to revive old wood finishes. This naturally thin viscosity oil will penetrate well on porous surfaces.

Safe for wood items in kitchens, such as cutting boards, wooden utensils, and countertops. Less durable and not as water resistant as Pure Tung Oil. Great for lightly used items. Takes 7 to 10 days for a partial cure, 15 to 30 for a full cure.

The color of oil can range from a light green to golden yellow depending on weather conditions and time of harvest. Primary advantage over Pure Tung Oil is the viscosity of Hemp Oil in that it requires no thinning with Citrus Solvent. However, it can be thinned with Citrus Solvent if a thinner viscosity is required

Hemp Oil is not reported to cause allergic reactions. However, we recommend that sensitive individuals do their own evaluation.

Some other’s are promoting Hemp Oil as a good way to revive leather boots or other leather goods. DON’T DO IT! Because Hemp Oil is a drying oil it will soak into leather and dry. This will cause the leather to crack and prematurely destroy your leather goods. Repeated applications of Hemp Oil to leather will just speed of the destruction. Use oil products made to treat leather. These will protect your leather goods for the long term.

Direction for Use

Preparation

  1. The best operating temperature for applying Half & Half is above 50°F (10°C ).
  2. Be sure the surface of your project is free of dust, debris, or grime.
  3. If you need to sand your surface, we recommend not going above 220 grit sandpaper. Too high of a sandpaper grit will “polish” the surface, hindering proper absorption of Hemp Oil.
  4. We recommend using water or alcohol-based stains on the wood before the Half & Half is applied. Most oil-based stains should be avoided as they tend to seal the wood and prevent absorption of the Half & Half.
  5. DO NOT use a wood conditioner. This will seal the wood and prevent the tung oil from absorbing.

Application

When applying Hemp Oil over an existing finish for furniture or finish restoration follow these steps.

  1. Apply Hemp Oil with a lint free cloth, such as an old t-shirt.
  2. Wipe onto surface liberally
  3. Allow oil to soak into the surface for 40 minutes.
  4. Wipe off any excess oil that may be on the surface.
  5. Allow Hemp Oil to 7 to 10 days before use.

When applying Hemp Oil on raw wood, here’s a handy thing to remember: Apply, Absorb, Repeat or Remove

Apply – Apply the Hemp Oil to the surface.

Absorb – Let the oil absorb into the material.

Repeat – Do what you just did, apply the oil and let it absorb.

Remove – When the oil isn’t absorbing and pooling on the surface, remove it with a rag.

Cure – Let the Hemp Oil go through its natural curing process.

For the best results, you want to saturate the material with the hemp oil to the point where a majority of the surface is no longer absorbing the oil. This will look like puddles on the surface even after waiting 40 minutes. Just like a sponge, the wood (or other porous surfaces) will only absorb so much oil before it can’t anymore. This saturation is achieved by doing multiple coats.

You can apply Hemp Oil with a brush, rag, roller, or even a pump sprayer depending on your project and needs. We recommend brushes and/or foam rollers for most projects.

  1. Apply a generous first coat.
  2. Let the hemp oil absorb into the surface, waiting if needed, up to 40 minutes.
  3. Apply another coat, let it absorb, and repeat the previous steps.
  4. Continue this process until you reach the desired amount of coats or have fully saturated the wood. You can tell the wood is saturated when the oil puddles on the surface and no longer absorbs oil across a majority of the surface. To be sure, wait 40 minutes. If the oil is still puddling, then you will know the surface is saturated.
  5. Taking a clean rag or cloth, remove any excess tung oil that is puddling or pooling on the surface.
  6. Hang those oil-soaked rags outdoors to dry. DO NOT pile the rags or put them in a container.

For the best finish, we recommend letting this application rest and settle overnight. The following day, apply one or two more coats of Hemp Oil to the surface of your project, following the same steps outlined above.

Cure –  Hemp Oil does not contain any additives to speed the drying process, such as heavy metallic dryers. Because of this, it can take up to 30 days to completely/thoroughly cure by its natural polymerization process. Provided below are some guidelines to follow during the curing phase.

  1. Hemp Oil cures best in warm, well-ventilated places. The warmer and more ventilated the area, the faster it will cure.
  2. Placing objects on the surface will “suffocate” and prevent the hemp oil from curing properly. If there is no airflow between the surface and the object, it should be removed until the curing is complete (30 days).
  3. During the first 15 days of curing, you can use the surface. However, you will want to avoid getting it dirty or allowing liquids to puddle on the surface during this period.
  4. As the Hemp Oil cures, its durability and resistance to liquids and dirt will also increase. The first 7-15 days is when the oil is at its freshest and weakest state. After that point, increased regular use of the surface can take place.
  5. As the Hemp Oil cures, it slightly expands and may push fresh oil back to the surface. Check for oil that may be seeping to the surface and remove it, if found, with a rag.

For butcher block, wood countertops, and etc.

  1. Avoid getting dirt, water, or other liquids on the surface of the butcher block for at least the first 7-10 days.
  2. We recommend putting wax paper down near sinks when doing dishes and other activities that splash water about. This will prevent the water from pooling on the surface and can be easily removed after dishwashing.
  3. Avoid putting cutting boards, appliances, dishes, and other objects that sit close to the recently refinished surface for extended periods of time. These objects prevent airflow and can hinder the tung oil from curing.
  4. If you are mounting or under mounting a sink, we recommend waiting for 7-10 days before mounting the sink. For caulk, we recommend using DAP Ultra Clear All Purpose Sealer. Silicone caulks tend to pull away from the oiled surface over time.
  5. If you have an under-mount sink, we highly recommend saturating the end grain of the butcherblock in the sink area with 100% Pure Tung Oil. This will help seal the very porous ends of the wood and give it the best resistance to water.

Tips

  1. Hemp Oil can be applied to any porous surfaces.
  2. Hemp Oil is also a great wood finish restorer. It can repair worn wood finishes just by simply wiping it onto the surface of the wood.
  3. Hemp Oil is especially useful for sealing and protecting wooden kitchen items such as cutting boards, wooden utensils, wooden bowls, and the like!
  4. When applying Hemp Oil over a milk painted surface, we recommend buffing the surface with a soft cloth prior to application of the oil. This will help remove any loose pigments from the surface.
  5. The number of coats of oil to be applied will be determined by the intended use of the piece. One to two coats are enough for decorative work, paneling and molding. For surfaces that receive moderate to heavy use or handling need a minimum of three and on up to six coats for maximum protection. Hemp Oil is best used for lightly to moderately used items. Pure Tung Oil is more durable and thus should be used for surfaces expected to get heavy use.
  6. Apply till the surface reaches the saturation point. This will be evident as the surface will not absorb more oil.
  7. Do not get hung up on the number of coats, let the wood tell you when it has reached its maximum saturation.
  8. The Hemp Oil will be in the wood up to the surface not on the wood surface like varnish or polyurethane topcoat. The end result is more like seasoning a cast iron pan. This product will give you a surface that will stand up to use and spills: water will bead on the surface.
  9. Renewal and/or maintenance coats are thinly applied with cheesecloth, lint-free cloths (old bed sheets work well), or old t-shirt material on an as need be basis.
  10. After the Hemp Oil has completely cured (minimum 30 days) cleaning of the surface can be done using hot water and mild soap, such as dish soap. Avoid using hard chemicals or acids for cleaning.

 

Maintenance

The beautiful thing about Hemp Oil finish is that the maintenance of it is easy. We recommend cleaning the floor with mild soap and hot water. Avoid using harsh chemicals, acids, or strong solvents to clean the surface.

Maintenance coats are on an as-need basis. Some well-used surfaces may require more frequent maintenance than others. Typically, surfaces that need maintenance have a very dry, or lackluster appearance compared to when the finish was originally applied.

When doing a maintenance coat you do not need to sand the surface again. Here is what we recommend;

    1. Apply Hemp Oil with a lint free cloth, such as an old t-shirt.
    2. Wipe onto surface liberally
    3. Allow oil to soak into the surface for 40 minutes.
    4. Wipe off any excess oil that may be on the surface.
    5. Allow Hemp Oil to 7 to 10 days before use.
    6. Hang oil-soaked rags outdoors to dry.
    7. Go back to enjoying the surface like normal!

Storage

Hemp Oil can last with ease for multiple years on the shelf. Here are some guidelines to help you store it properly so it can be used for your next project.

  1. Make sure the lid on the Hemp Oil packaging is tightly screwed on. This will keep air exchange from happening in the container.
  2. Store the bottle in a dry, moderate temperature environment. A place where it won’t freeze or become excessively hot. Freezing of the oil will make the natural fats separate from the oil. Excessive heat can cook the oil to the point where it cures in the bottle.

 

What Its Made Of

We believe in being honest with what is in our products. So, thats why we provide the ingredients used in them so you can rest assured knowing exactly whats in the product you purchase from us. Its just a way we make it easier on you.

Hemp Oil is made of

  • Industrial Hemp Oil

Details

  • Our Hemp Oil is derived from cold pressed industrial hemp.
  •  

Take a look at our Hemp Oil Safety Data Sheet (SDS) by clicking here.

MSDS

Keep containers tightly closed away from extreme temperature changes and open flames. As with all oils, rags, steel wool or waste soaked with oil, may spontaneously catch fire if improperly discarded. Immediately after use, place the oil soaked material in a sealed water-filled metal container or hang outside separately to dry.

At Faifer & Company, Inc. as well as The Real Milk Paint Company we do our best to provide safe products as well as information. However we can not guarantee that individuals with compromised immune systems or allergies will not have a reaction to our products. We strongly recommend that each person take their own personal responsibility in testing this product for their own personal use.